Description:
    This batch file attempts to verify that the online serial port 
diagnostic commands
    can be executed.
   
******************************************************************************************

    Clear the Expected Batch File Errors.
   
******************************************************************************************

    -*9                                 All Level '*' Command: Special 
Batch File Function - Clear Expected Errors
   
******************************************************************************************

    Display the help information for the Online Commands.
   
******************************************************************************************

    -/CQ^                               Level C 'Q' Command: Display 
ASCII Command Information
   
******************************************************************************************

    Select Online Serial Port Mode.
   
    Note: This command will be executed on the first pass but not on the
 second pass.
   
******************************************************************************************

    -^R                                 Control R Command: Enable ASCII 
Online Serial Port Mode
    -*7,2,0                             '*' Command: Special Batch File 
Function - Set Loop Count 0 to 2
    -*3,1                               '*' Command: Special Batch File 
Function - Branch to Label 1
   
******************************************************************************************

    Select Diagnostic Serial Port Mode, enable error logging and clear 
the error log.
   
    Note: These commands will be executed on the second pass but not the
 first pass.
   
******************************************************************************************

    -@0                                 '@' Command: Batch File Label - 
Label 0
    -^Z                                 Control Z Command: Enable ASCII 
Diagnostic Serial Port Mode
    -/LE1                               Level L 'E' Command: Enable / 
Disable Logging
    -/LiFFFC                            Level L 'i' Command: Initialize 
Log File (Default Error Log)
   
******************************************************************************************

    Test the Online Commands.  This section of the code will be executed
 twice, first with
    Online Serial Port Mode enabled and then with Diagnostic Serial Port
 Mode enabled.
   
******************************************************************************************

    -@1                                 '@' Command: Batch File Label - 
Label 1
    -CR                                 Carriage Return Command: Abort
    -!                                  '!' Command: Display Current 
Read Channel Settings
    -^W                                 Control W Command: Enable and 
Init RW Statistics
    -$                                  '$' Command: Display Read/Write 
Statistics By Zone
    -`                                  '`' Command: Display Read/Write 
Statistics
    -.                                  '.' Command: Display Active 
Status
    -<                                  '<' Command: Decrement 
Read/Write Scope Sync
    ->                                  '>' Command: Increment 
Read/Write Scope Sync
    -?                                  '?' Command: Display Diagnostic 
Buffer Information
    -*7,8,1                             '*' Command: Special Batch File 
Function - Set Loop Count 1 to 8
    -@2                                 '@' Command: Batch File Label - 
Label 2
    -{                                  '{' Command: Toggle EIB-Specific
 R/W Tracing
    -*8,2,1                             '*' Command: Special Batch File 
Function (Decrement Loop Count 1 and Branch to Label 2 if not 0)
    -~                                  '~' Command: Display Native 
Interface Command State
    -^A                                 Control A Command: Display 
Firmware Revision
    -^B                                 Control B Command: Get 
Thermistor Temperature
    -*7,8,1                             '*' Command: Special Batch File 
Function - Set Loop Count 1 to 8
    -@3                                 '@' Command: Batch File Label - 
Label 3
    -^D                                 Control D Command: Toggle R/W 
Tracing
    *8,3,1                              '*' Command: Special Batch File 
Function (Decrement Loop Count 1 and Branch to Label 3 if not 0)
    -^E                                 Control E Command: Display 
Native Interface Configuration
    -^F                                 Control F Command: Display 
Native Interface Read Cache Information
    -^I                                 Control I Command: Display 
Controller Registers
    -^K                                 Control K Command: Display DST 
Status
    -^L                                 Control L Command: Display Sign 
On Message
    -*7,8,1                             '*' Command: Special Batch File 
Function - Set Loop Count 1 to 8
    -@4                                 '@' Command: Batch File Label - 
Label 4
    -^N                                 Control N Command: Toggle R/W 
Tracing
    -*8,4,1                             '*' Command: Special Batch File 
Function (Decrement Loop Count 1 and Branch to Label 4 if not 0)
    -^P                                 Control P Command: Toggle Diag 
Idle Mode
    -^P                                 Control P Command: Toggle Diag 
Idle Mode
    -^S                                 Control S Command: Pause 
Interface Task
    -^Q                                 Control Q Command: Resume 
Interface Task
    -^U                                 Control U Command: Display 
Congen
    -^V                                 Control V Command: Toggle 
Interface Command Echo
    -^V                                 Control V Command: Toggle 
Interface Command Echo
    -^X                                 Control X Command: Display 
Native Interface and Read/Write Command History
    -^Y                                 Control Y Command: Display DST 
Status
    -^\                                 Control \ Command: Toggle Debug 
Display Enable
    -^\                                 Control \ Command: Toggle Debug 
Display Enable
    -*8,0,0                             '*' Command: Special Batch File 
Function (Decrement Loop Count 0 and Branch to Label 0 if not 0)
   
   
******************************************************************************************

    Display the Active Error Log and check if the Batch File failed.
   
******************************************************************************************

    -*B                                 All Level '*' Command: Special 
Batch File Function - Display Log
    -|                                  '|' Command: Batch File 
Terminator